Document Number: 001-74584 Rev. *C Page 9 of 30
Truth Table
The truth table for CY7C1365C follows.
[1, 2, 3, 4, 5]
Cycle Description Address Used CE
1
CE
3
CE
2
ZZ ADSP ADSC ADV WRITE OE CLK DQ
Deselected Cycle, Power-down None H X X L X L X X X L–H Tri-State
Deselected Cycle, Power-down None L X L L L X X X X L–H Tri-State
Deselected Cycle, Power-down None L H X L L X X X X L–H Tri-State
Deselected Cycle, Power-down None L X L L H L X X X L–H Tri-State
Deselected Cycle, Power-down None X X X L H L X X X L–H Tri-State
Sleep Mode, Power-down None X X X H X X X X X X Tri-State
Read Cycle, Begin Burst External L L H L L X X X L L–H Q
Read Cycle, Begin Burst External L L H L L X X X H L–H Tri-State
Write Cycle, Begin Burst External L L H L H L X L X L–H D
Read Cycle, Begin Burst External L L H L H L X H L L–H Q
Read Cycle, Begin Burst External L L H L H L X H H L–H Tri-State
Read Cycle, Continue Burst Next X X X L H H L H L L–H Q
Read Cycle, Continue Burst Next X X X L H H L H H L–H Tri-State
Read Cycle, Continue Burst Next H X X L X H L H L L–H Q
Read Cycle, Continue Burst Next H X X L X H L H H L–H Tri-State
Write Cycle, Continue Burst Next X X X L H H L L X L–H D
Write Cycle, Continue Burst Next H X X L X H L L X L–H D
Read Cycle, Suspend Burst Current X X X L H H H H L L–H Q
Read Cycle, Suspend Burst Current X X X L H H H H H L–H Tri-State
Read Cycle, Suspend Burst Current H X X L X H H H L L–H Q
Read Cycle, Suspend Burst Current H X X L X H H H H L–H Tri-State
Write Cycle, Suspend Burst Current X X X L H H H L X L–H D
Write Cycle, Suspend Burst Current H X X L X H H L X L–H D
Notes
1. X = “Don't Care.” H = Logic HIGH, L = Logic LOW.
2. WRITE
= L when any one or more Byte Write Enable signals (BW
A
, BW
B
, BW
C
, BW
D
) and BWE = L or GW = L. WRITE = H when all Byte Write Enable signals (BW
A
,
BW
B
, BW
C
, BW
D
), BWE, GW = H.
3. The DQ pins are controlled by the current cycle and the OE
signal. OE is asynchronous and is not sampled with the clock.
4. The SRAM always initiates a Read cycle when ADSP
is asserted, regardless of the state of GW, BWE, or BW
[A: D]
. Writes may occur only on subsequent clocks after
the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to tri-state. OE is a don't care
for the remainder of the Write cycle.
5. OE
is asynchronous and is not sampled with the clock rise. It is masked internally during Write cycles. During a read cycle all data bits are Tri-State when OE is inactive
or when the device is deselected, and all data bits behave as output when OE
is active (LOW).
(36 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales