CY7B9911V
3.3V RoboClock+™
Document #: 38-07408 Rev. *B Page 8 of 12
Capacitance
[10]
Parameter Description Test Conditions Max. Unit
C
IN
Input Capacitance T
A
= 25°C, f = 1 MHz, V
CC
= 3.3V 10 pF
AC Test Loads and Waveforms
Switching Characteristics Over the Operating Range
[2, 11]
Parameter Description
CY7B9911V-5
UnitMin. Typ. Max.
f
NOM
Operating Clock
Frequency in MHz
FS = LOW
[1, 2]
15 30 MHz
FS = MID
[1, 2]
25 50
FS = HIGH
[1, 2 , 3]
40 110
t
RPWH
REF Pulse Width HIGH 5.0 ns
t
RPWL
REF Pulse Width LOW 5.0 ns
t
U
Programmable Skew Unit See Table 1
t
SKEWPR
Zero Output Matched-Pair Skew (XQ0, XQ1)
[13, 14]
0.1 0.25 ns
t
SKEW0
Zero Output Skew (All Outputs)
[13, 15]
0.25 0.5 ns
t
SKEW1
Output Skew (Rise-Rise, Fall-Fall, Same Class Outputs)
[13, 17]
0.6 0.7 ns
t
SKEW2
Output Skew (Rise-Fall, Nominal-Inverted, Divided-Divided)
[13, 17]
0.5 1.0 ns
t
SKEW3
Output Skew (Rise-Rise, Fall-Fall, Different Class Outputs)
[13, 17]
0.5 0.7 ns
t
SKEW4
Output Skew (Rise-Fall, Nominal-Divided, Divided-Inverted)
[13, 17]
0.5 1.0 ns
t
DEV
Device-to-Device Skew
[12, 18]
1.25 ns
t
PD
Propagation Delay, REF Rise to FB Rise –0.5 0.0 +0.5 ns
t
ODCV
Output Duty Cycle Variation
[19]
–1.0 0.0 +1.0 ns
t
PWH
Output HIGH Time Deviation from 50%
[20]
2.5 ns
t
PWL
Output LOW Time Deviation from 50%
[20]
3ns
t
ORISE
Output Rise Time
[20, 21]
0.15 1.0 1.5 ns
t
OFALL
Output Fall Time
[20, 21]
0.15 1.0 1.5 ns
t
LOCK
PLL Lock Time
[22]
0.5 ms
Notes:
11. Test measurement levels for the CY7B9911V are TTL levels (1.5V to 1.5V). Test conditions assume signal transition times of 2 ns or less and output loading as shown
in the AC Test Loads and Waveforms unless otherwise specified.
12. Guaranteed by statistical correlation. Tested initially and after any design or process changes that may affect these parameters.
13. SKEW is defined as the time between the earliest and the latest output transition among all outputs for which the same t
U
delay has been selected when all are
loaded with 30 pF and terminated with 50Ω to V
CC
/2 (CY7B9911V).
14. t
SKEWPR
is defined as the skew between a pair of outputs (XQ0 and XQ1) when all eight outputs are selected for 0t
U
.
15. t
SKEW0
is defined as the skew between outputs when they are selected for 0t
U
. Other outputs are divided or inverted but not shifted.
16. C
L
=0 pF. For C
L
=30 pF, t
SKEW0
=0.35 ns.
17. There are three classes of outputs: Nominal (multiple of t
U
delay), Inverted (4Q0 and 4Q1 only with 4F0 = 4F1 = HIGH), and Divided (3Qx and 4Qx only in Divide-by-2
or Divide-by-4 mode).
18. t
DEV
is the output-to-output skew between any two devices operating under the same conditions (V
CC
ambient temperature, air flow, etc.)
19. t
ODCV
is the deviation of the output from a 50% duty cycle. Output pulse width variations are included in t
SKEW2
and t
SKEW4
specifications.
20. Specified with outputs loaded with 30 pF for the CY7B9911V-5 and -7 devices. Devices are terminated through 50Ω to V
CC
/2.t
PWH
is measured at 2.0V. t
PWL
is
measured at 0.8V.
21. t
ORISE
and t
OFALL
measured between 0.8V and 2.0V.
22. t
LOCK
is the time that is required before synchronization is achieved. This specification is valid only after V
CC
is stable and within normal operating limits. This parameter is
measured from the application of a new signal or frequency at REF or FB until t
PD
is within specified limits.
TTL ACTest Load TTL Input Test Waveform
V
CC
R1
R2
C
L
3.0V
2.0V
V
th
=1.5V
0.8V
0.0V
≤1ns
≤1ns
2.0V
0.8V
V
th
=1.5V
R1=100
R2=100
C
L
=30pF
(Includes fixture and probe capacitance)
(14 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales